[BSD] FreeBSD 9.1 on Fujitsu Primergy Tx150 S8

Lévai László laszlo.lev.levai at gmail.com
2013. Május. 10., P, 11:08:01 CEST

Hash: SHA1


Van most a kezem alatt egy Primergy TX150 S8 szerver, melyre
kíváncsiságból felraktam egy FreeBSD 9.1-et. Az kell, hogy mondjam, a
hardver támogatása kiváló, minden hardvert felismert a dobozban.

A konfig a teljesség igénye nélkül:
1db Intel Xeon E5-2407 4C/4T 2.20 GHz 10 MB
1db 4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC
1db DVD-RW supermulti slimline SATA
2db HD SATA 6G 1TB 7.2K HOT PL 3.5" BC
1db RAID Ctrl SAS 6G 0/1 (D2607)

dmesg kimenet:
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.1-RELEASE #0 r243825: Tue Dec  4 09:23:10 UTC 2012
    root at farrell.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64
CPU: Intel(R) Xeon(R) CPU E5-2407 0 @ 2.20GHz (2200.05-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x206d7  Family = 6  Model = 2d
Stepping = 7


  AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant, performance statistics
real memory  = 4294967296 (4096 MB)
avail memory = 3986518016 (3801 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <FTS    A M I>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  2
 cpu2 (AP): APIC ID:  4
 cpu3 (AP): APIC ID:  6
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
kbd1 at kbdmux0
acpi0: <FTS A M I> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Event timer "HPET4" frequency 14318180 Hz quality 440
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 26 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 26 at device 1.1 on pci0
pci2: <ACPI PCI bus> on pcib2
mfi0: <Drake Skinny> port 0xe000-0xe0ff mem
0xfbc60000-0xfbc63fff,0xfbc00000-0xfbc3ffff irq 27 at device 0.0 on pci2
mfi0: Using MSI
mfi0: Megaraid SAS driver Ver 4.23
pcib3: <ACPI PCI-PCI bridge> irq 40 at device 3.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pci0: <base peripheral> at device 5.0 (no driver attached)
pci0: <base peripheral> at device 5.2 (no driver attached)
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 17.0 on pci0
pci4: <ACPI PCI bus> on pcib4
isci0: <Intel(R) C600 Series Chipset SAS Controller (SATA mode)> port
0xd000-0xd0ff mem 0xf9c7c000-0xf9c7ffff,0xf9800000-0xf9bfffff irq 16
at device 0.0 on pci4
pci4: <serial bus, SMBus> at device 0.3 (no driver attached)
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfbd03000-0xfbd033ff
irq 16 at device 26.0 on pci0
usbus0: EHCI version 1.0
usbus0 on ehci0
pcib5: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci5: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci6: <ACPI PCI bus> on pcib6
em0: <Intel(R) PRO/1000 Network Connection 7.3.2> port 0xc000-0xc01f
mem 0xfba00000-0xfba1ffff,0xfba20000-0xfba23fff irq 16 at device 0.0
on pci6
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:19:99:e2:b9:3a
pcib7: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci7: <ACPI PCI bus> on pcib7
em1: <Intel(R) PRO/1000 Network Connection 7.3.2> port 0xb000-0xb01f
mem 0xfb900000-0xfb91ffff,0xfb920000-0xfb923fff irq 17 at device 0.0
on pci7
em1: Using MSIX interrupts with 3 vectors
em1: Ethernet address: 00:19:99:e2:b9:3b
pcib8: <ACPI PCI-PCI bridge> irq 19 at device 28.7 on pci0
pci8: <ACPI PCI bus> on pcib8
vgapci0: <VGA-compatible display> mem
0xfa000000-0xfaffffff,0xfb800000-0xfb803fff,0xfb000000-0xfb7fffff irq
19 at device 0.0 on pci8
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfbd02000-0xfbd023ff
irq 23 at device 29.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci1
pcib9: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci9: <ACPI PCI bus> on pcib9
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci0: <Intel Patsburg AHCI SATA controller> port
mem 0xfbd01000-0xfbd017ff irq 19 at device 31.2 on pci0
ahci0: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcib10: <ACPI Host-PCI bridge> on acpi0
pci255: <ACPI PCI bus> on pcib10
acpi_button0: <Power Button> on acpi0
acpi_acad0: <AC Adapter> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xcf000-0xcffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: cannot reserve I/O port range
ctl: CAM Target Layer loaded
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
mfi0: 304 (421497472s/0x0020/info) - Shutdown command received from host
mfi0: 305 (boot + 3s/0x0020/info) - Firmware initialization started
(PCI ID 0073/1000/1177/1734)
mfi0: 306 (boot + 3s/0x0020/info) - Firmware version 2.130.354-1820
mfi0: 307 (boot + 5s/0x0020/info) - Package version 20.10.1-0120
mfi0: 308 (boot + 5s/0x0020/info) - Board Revision
mfi0: 309 (boot + 39s/0x0002/info) - Inserted: PD 04(e0xff/s4)
mfi0: 310 (boot + 39s/0x0002/info) - Inserted: PD 04(e0xff/s4) Info:
enclPd=ffff, scsiType=0, portMap=01,
mfi0: 311 (boot + 39s/0x0002/info) - Inserted: PD 05(e0xff/s5)
mfi0: 312 (boot + 39s/0x0002/info) - Inserted: PD 05(e0xff/s5) Info:
enclPd=ffff, scsiType=0, portMap=00,
mfi0: 313 (421497534s/0x0020/info) - Time established as 05/10/13
10:38:54; (42 seconds since power on)
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
mfid0 on mfi0
mfid0: 953344MB (1952448512 sectors) RAID volume 'tank0' is optimal
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr
2> on usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr
2> on usbus1
uhub2: 6 ports with 6 removable, self powered
uhub3: 8 ports with 8 removable, self powered
ugen1.3: <vendor 0x0424> at usbus1
uhub4: <vendor 0x0424 product 0x2514, class 9/0, rev 2.00/b.b3, addr
3> on usbus1
uhub4: MTT enabled
cd0 at ahcich0 bus 0 scbus1 target 0 lun 0
cd0: <HL-DT-ST DVDRAM GT80N SF02> Removable CD-ROM SCSI-0 device
cd0: 150.000MB/s transfers (SMP: AP CPU #2 Launched!
SATA 1.x, UDMA6, ATAPI 12bytes, PIO 8192bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not
present - tray closed
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
Timecounter "TSC-low" frequency 8593937 Hz quality 1000
Root mount waiting for: usbus1
uhub4: 2 ports with 2 removable, self powered
ugen1.4: <vendor 0x0424> at usbus1
uhub5: <vendor 0x0424 product 0x2514, class 9/0, rev 2.00/b.b3, addr
4> on usbus1
uhub5: MTT enabled
Root mount waiting for: usbus1
uhub5: 4 ports with 4 removable, self powered
ugen1.5: <Chicony> at usbus1
ukbd0: <Chicony Multimedia Keyboard, class 0/0, rev 2.00/1.00, addr 5>
on usbus1
kbd0 at ukbd0
Root mount waiting for: usbus1
uhid0: <Chicony Multimedia Keyboard, class 0/0, rev 2.00/1.00, addr 5>
on usbus1
Trying to mount root from ufs:/dev/mfid0p2 [rw]...
ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is
            to enable, add "vfs.zfs.prefetch_disable=0" to
ZFS filesystem version 5
ZFS storage pool version 28

SAS Raid:
mfi0 Physical Drives:
 4 (  931G) ONLINE <ST1000NM0011 FTM4 serial=Z1N3XKEH> SATA E1:S4
 5 (  931G) ONLINE <ST1000NM0011 FTM4 serial=Z1N3XKBR> SATA E1:S5

mfi0 Adapter:
    Product Name: RAID Ctrl SAS 6G 0/1 (D2607)
   Serial Number:
        Firmware: 20.10.1-0120
     RAID Levels: JBOD, RAID0, RAID1, RAID10
  Battery Backup: not present
           NVRAM: 32K
  Onboard Memory: 0M
  Minimum Stripe: 8k
  Maximum Stripe: 64k

Vétek ilyen gépre Centos-t telepíteni...

- -- 
Lévai László
Version: GnuPG v1.4.13 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/


További információk a(z) BSD levelezőlistáról