[BSD] FreeBSD-képes laptop

[Marton Kenyeres]

On Tuesday 27 July 2004 18:58, Zahemszky Gábor wrote:
> Marton Kenyeres írta:
> > Azt nem tudom, hogy fbsd fronton mi az aktualis helyzet, de nekem van egy
> > ilyen kartyam, ami NetBSD 1.6 alatt szepen megjelenik mint halokartya
> > *es* modem. Holnap tudok dmesg-et kuldeni, ha erdekel valakit.
>
> Kérném, valamint mindenféle infót a driveréről. Természetesen a modem
> fele érdekel. De jöhet magánban is.
>
> Köszi!
>
> Zahy < Gabor at Zahemszky dot HU >

Hello,

A szobanforgo kartya egy 3com 3c562D/3c563D 10-es halo/33.6 modem combo. A gep 
amiben uzemel egy Toshiba Libretto 100CT. A halokartya resze ep, a modem sima 
com drivert hasznal. A kernel config gyakorlatilag GENERIC_LAPTOP, csak 
kivettem belole mindent, ami nincs a gepben. dmesg mellekelve.

udv, 
m.


--------- következő rész ---------
NetBSD 1.6 (BEASTIE) #0: Sun Nov 10 12:12:13 CET 2002
    toor at beastie.kvg.hu:/usr/src/sys/arch/i386/compile/BEASTIE
cpu0: Intel Pentium/MMX (Tillamook) (586-class), 166.65 MHz
cpu0: features 8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
cpu0: features 8001bf<MMX>
total memory = 32444 KB
avail memory = 28644 KB
using 431 buffers containing 1724 KB of memory
BIOS32 rev. 0 found at 0xfe95a
PCI BIOS rev. 2.1 found at 0xfc5f8
PCI IRQ Routing Table rev. 1.0 found at 0xf8e80, size 112 bytes (5 entries)
PCI Interrupt Router at 000:01:0 (vendor 0x1179 product 0x0602)
pci_intr_fixup: no compatible PCI ICU found: ICU vendor 0xffff product 0xffff
Warning: unable to fix up PCI interrupt routing
pci_addr_fixup: 000:19:0 0x1179 0x060a new address 0x02100000
pci_addr_fixup: 000:19:1 0x1179 0x060a new address 0x02101000
mainbus0 (root)
pnpbios0 at mainbus0: nodes 15, max len 195
pnpbios0: not docked
pnpbios0: node index mismatch (static): requested 0, got 1
ym0 at pnpbios0 index 22 (YMH0021)
ym0: io 220-22f 530-537 388-38f 330-331 370-371, irq 5, dma 1 0
ym0: OPL3-SA3
audio0 at ym0: full duplex, mmap
opl0 at ym0: model OPL3
midi0 at opl0: OPL3-SA3 Yamaha OPL3
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1179 product 0x0601 (rev. 0x2e)
vga0 at pci0 dev 4 function 0: vendor 0x10c8 product 0x0004 (rev. 0x01)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
oboe0 at pci0 dev 17 function 0: Toshiba Fast Infrared Type O, revision 34
oboe0: interrupting at irq 11
irframe0 at oboe0: SIR, MIR, FIR
cbb0 at pci0 dev 19 function 0: vendor 0x1179 product 0x060a (rev. 0x07)
cbb1 at pci0 dev 19 function 1: vendor 0x1179 product 0x060a (rev. 0x07)
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 2 device 0
pcmcia1 at cardslot1
isa0 at mainbus0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
wd0 at wdc0 channel 0 drive 0: <TOSHIBA MK2105MAT>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 2067 MB, 4200 cyl, 16 head, 63 sec, 512 bytes/sect x 4233600 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff: using exception 16
apm0 at mainbus0: Power Management spec V1.2
biomask ef4d netmask ef4d ttymask ffcf
ep0 at pcmcia0 function 0: 3Com 3c562 33.6 Modem/10Mbps Ethernet
ep0: address 00:60:97:ee:fe:e3, 8KB byte-wide FIFO, 5:3 Rx:Tx split
ep0: 10baseT, 10base5, 10base2 (default 10baseT)
com1 at pcmcia0 function 1: serial device
com1: ns16550a, working fifo
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)